Coolant Flush and Replacement - C Class - W204 - Mercedes-Benz



Coolant Flush and Replacement - C Class - W204 - Mercedes-Benz


Coolant Flush and Replacement Time: 2 hours Tab: $25 to $45 Talent: 2 Tools: Pliers, 6mm Allen, large bucket, floor jack, jack stands, wheelchocks, safety glasses Applicable Models: Mercedes-Benz C350 (2008-15) Mercedes-Benz GLK350 (2010-15) Parts Required: New coolant Hot Tip: Get a really big bucket Performance Gain: Proper cooling Complementary Modification: New hoses If you are changing your coolant this is also the perfect time to give your cooling system a complete flush. While it is next to impossible to get all of the coolant and contaminants out of the system without removing the heater core lines and blowing out the heating system this method will get the system as clean as possible and more than good enough for the next ten years. A couple of safety precautions/instructions you may want to observe before beginning: Allow the cooling system to cool down to a coolant temperature of less than 80 degrees C. Open the cap of the cooling system slowly; turn a conventional coolant cap as far as the first detent and turn a screwed coolant cap approx. 1/2 turn and release the pressure. Wear protective gloves, protective clothing and eye protection. NEVER pour coolant into beverage bottles, cups, etc.. Someone might accidentally pick that cup up and start to drink. Always dispose of your used coolant correctly and in accordance with your local regulations. Never pour it down a drain or in the ground. If you are going to drain the coolant from the block you are going to be working around the starter motor, as the block drain plug is located right beside the starter. I highly, highly recommend you disconnect the battery, as the chance of harming yourself and the vehicle is greatly increased once everything is wet with coolant. Refresh your vehicles coolant with a good flush and replacement Applies to: C350 (2007-14), SLK350 (2004-14), CLS350 (2004-14), CLK350 (2005-14), E350 (2005-14), S350 (2005-14), SL350 (2005-14), R350 (2006-14), ML350 (2006-14), Viano (2005-14), Sprinter (2006-14), CLC350 (2008-14), GLK350 (2008-12)

Comments

Post a Comment

Popular posts from this blog

Crankshaft Positioning Sensor Replacement - C Class - W204 - Mercedes-Benz

Image
Crankshaft Positioning Sensor Replacement - C Class - W204 - Mercedes-Benz Crankshaft Positioning Sensor Replacement Time: 2 hours Tab: $20 to $40 Talent: 1 Tools: T30 Torx Applicable Models: Mercedes-Benz C350 (2008-14) Mercedes-Benz GLK350 (2010-14) Parts Required: Crankshaft positioning sensor Hot Tip: Use a mirror Performance Gain: Smoother running car Complementary Modification: Replace Camshaft positioning sensors Your fuel injection computer (DME) may output a code that indicates a faulty camshaft position sensor (CPS). This important sensor tells the car's computer where the flywheel is located in relation to the combustion cycle. The DME takes the signals from both the cam position sensor and crankshaft position sensor, and calculates when to fire the fuel injectors and spark plugs. If the crankshaft position sensor is not operating properly, your car will run very erratically or perhaps not at all. Replacement of the sensor is not as easy as the camshaf...
Read more

Yaw Rate Sensor Replacement - C Class - W204 - Mercedes-Benz

Image
Yaw Rate Sensor Replacement - C Class - W204 - Mercedes-Benz Yaw Rate Sensor Replacement Time: 2 hours Tab: $320 Talent: 2 Tools: Trim removal tool, E12 socket, T45 Torx driver, 10mm socket or wrench Applicable Models: Mercedes-Benz C250 (2012-14) Mercedes-Benz C300 (2008-14) Mercedes-Benz C350 (2008-14) Parts Required: Yaw rate sensor Hot Tip: The sensors are sensitive to shock; use care when working with them Performance Gain: Working ESP Complementary Modification: Clean carpet and interior beneath seats The yaw rate sensor is located below the driver side seat and is used to measure the yaw, lateral and longitudinal acceleration of the rotation around a vertical axis. This sensor is used to supply information to the Electronic Stability Program and has been known to fail in the past. If you are getting an error code for the yaw sensor and need to replace it this article will show you how. The sensors are sensitive to impact so use care when working with it and be ca...
Read more

Front Stabilizer Bar Replacement - C Class - W204 - Mercedes-Benz

Image
Front Stabilizer Bar Replacement - C Class - W204 - Mercedes-Benz Front Stabilizer Bar Replacement Time: 2 hours Tab: $170 Talent:2 Tools: E12 Torx, T40 Torx, 18mm, 13mm wrench Applicable Models: Mercedes-Benz C250 (2012-14) Mercedes-Benz C300 (2008-14) Mercedes-Benz C350 (2008-14) Parts Required: New stabilizer bar and hardware Hot Tip: Don't let the bar fall on you Performance Gain: Better handling If you are starting to hear a knock sound when you go around a corner there is a good chance your sway or stabilizer bar bushings are starting to go bad. Unfortunately, the rubber bushings on the stabilizer on the W204 are vulcanized to the bar and cannot be replaced separately. This means you will need to drop the bar and replace it with a new one. All of the mounting hardware is considered single use so make sure you order new hardware when ordering the bar. You will need to jack up the car and remove the front wheels along with the under body trays to perform...
Read more