Engine Cover Removal - C Class - W204 - Mercedes-Benz



Engine Cover Removal - C Class - W204 - Mercedes-Benz


Time: 10 minutes, Tab: $0, Talent: 1 Tools: Hands, Applicable Models: Mercedes-Benz C300 Luxury Sedan 2011 Mercedes-Benz C350 (2008-15) Mercedes-Benz GLK350 (2010-15) Hot Tip: Wiggle and pull at the same time Performance Gain: Access to the engine systems Complementary Modification: Change cabin air filter There are two engine covers on the C350 along with two air ducts that you will need to remove to perform just about any work on the motor. Removal is simple and easy and needs no tools other than your hands. Note: On the 2013 C300 4Matic you will need to remove the engine cover, vacuum line bracket and air ducts. There is also sound insulation that has to come off--start by unclipping and removing the air filter, then the top cover and ducts. Applies to: C350 (2007-14), SLK350 (2004-14), CLS350 (2004-14), CLK350 (2005-14), E350 (2005-14), S350 (2005-14), SL350 (2005-14), R350 (2006-14), ML350 (2006-14), Viano (2005-14), Sprinter (2006-14), CLC350 (2008-14), GLK350 (2008-12)

Comments

Post a Comment

Popular posts from this blog

Crankshaft Positioning Sensor Replacement - C Class - W204 - Mercedes-Benz

Image
Crankshaft Positioning Sensor Replacement - C Class - W204 - Mercedes-Benz Crankshaft Positioning Sensor Replacement Time: 2 hours Tab: $20 to $40 Talent: 1 Tools: T30 Torx Applicable Models: Mercedes-Benz C350 (2008-14) Mercedes-Benz GLK350 (2010-14) Parts Required: Crankshaft positioning sensor Hot Tip: Use a mirror Performance Gain: Smoother running car Complementary Modification: Replace Camshaft positioning sensors Your fuel injection computer (DME) may output a code that indicates a faulty camshaft position sensor (CPS). This important sensor tells the car's computer where the flywheel is located in relation to the combustion cycle. The DME takes the signals from both the cam position sensor and crankshaft position sensor, and calculates when to fire the fuel injectors and spark plugs. If the crankshaft position sensor is not operating properly, your car will run very erratically or perhaps not at all. Replacement of the sensor is not as easy as the camshaf...
Read more

Yaw Rate Sensor Replacement - C Class - W204 - Mercedes-Benz

Image
Yaw Rate Sensor Replacement - C Class - W204 - Mercedes-Benz Yaw Rate Sensor Replacement Time: 2 hours Tab: $320 Talent: 2 Tools: Trim removal tool, E12 socket, T45 Torx driver, 10mm socket or wrench Applicable Models: Mercedes-Benz C250 (2012-14) Mercedes-Benz C300 (2008-14) Mercedes-Benz C350 (2008-14) Parts Required: Yaw rate sensor Hot Tip: The sensors are sensitive to shock; use care when working with them Performance Gain: Working ESP Complementary Modification: Clean carpet and interior beneath seats The yaw rate sensor is located below the driver side seat and is used to measure the yaw, lateral and longitudinal acceleration of the rotation around a vertical axis. This sensor is used to supply information to the Electronic Stability Program and has been known to fail in the past. If you are getting an error code for the yaw sensor and need to replace it this article will show you how. The sensors are sensitive to impact so use care when working with it and be ca...
Read more

Front Stabilizer Bar Replacement - C Class - W204 - Mercedes-Benz

Image
Front Stabilizer Bar Replacement - C Class - W204 - Mercedes-Benz Front Stabilizer Bar Replacement Time: 2 hours Tab: $170 Talent:2 Tools: E12 Torx, T40 Torx, 18mm, 13mm wrench Applicable Models: Mercedes-Benz C250 (2012-14) Mercedes-Benz C300 (2008-14) Mercedes-Benz C350 (2008-14) Parts Required: New stabilizer bar and hardware Hot Tip: Don't let the bar fall on you Performance Gain: Better handling If you are starting to hear a knock sound when you go around a corner there is a good chance your sway or stabilizer bar bushings are starting to go bad. Unfortunately, the rubber bushings on the stabilizer on the W204 are vulcanized to the bar and cannot be replaced separately. This means you will need to drop the bar and replace it with a new one. All of the mounting hardware is considered single use so make sure you order new hardware when ordering the bar. You will need to jack up the car and remove the front wheels along with the under body trays to perform...
Read more