Oil Level Sensor Replacement - C Class - W204 - Mercedes-Benz



Oil Level Sensor Replacement - C Class - W204 - Mercedes-Benz


Oil Level Sensor Replacement Time: 3 hours Tab: $30 to $50 Talent: 1 Tools: 13mm wrench, 8mm socket, E10 Torx, extension, floor jack, jackstands, wheel chocks, safety glasses, torque wrench Applicable Models: Mercedes-Benz C350 (2008-14) Mercedes-Benz GLK350 (2010-14) Parts Required: Oil level sensor, sealant, oil Hot Tip: Do NOT use anything metal between the mounting surfaces Performance Gain: Working sensor Complementary Modification: Change the oil filter If your oil level sensor has failed you will have to remove the oil pan to replace it and then you will need to clean the mounting surfaces really well and use a good high quality sealant. I recommend Drei Bond 1209. I have used this for years with great results, and it is available at Pelican Parts. Make sure to carefully follow the instructions on the sealant you choose to use and allow it to dry and seal completely. Also you do not need to use a lot of sealant. All the extra will do is squeeze out and make a mess outside and inside the cover. You are going to need to drain and refill the oil from the motor. If you are close to needing an oil and filter change now is a good time to change the filter as well. Get the engine warm before draining the oil. To begin this project safely jack up and support your car. Please see our article on safely jacking up and supporting your W204. Replace a failed oil level sensor with these step by step instructions Applies to: C350 (2007-14), SLK350 (2004-14), CLS350 (2004-14), CLK350 (2005-14), E350 (2005-14), S350 (2005-14), SL350 (2005-14), R350 (2006-14), ML350 (2006-14), Viano (2005-14), Sprinter (2006-14), CLC350 (2008-14), GLK350 (2008-12)

Comments

Post a Comment

Popular posts from this blog

Crankshaft Positioning Sensor Replacement - C Class - W204 - Mercedes-Benz

Image
Crankshaft Positioning Sensor Replacement - C Class - W204 - Mercedes-Benz Crankshaft Positioning Sensor Replacement Time: 2 hours Tab: $20 to $40 Talent: 1 Tools: T30 Torx Applicable Models: Mercedes-Benz C350 (2008-14) Mercedes-Benz GLK350 (2010-14) Parts Required: Crankshaft positioning sensor Hot Tip: Use a mirror Performance Gain: Smoother running car Complementary Modification: Replace Camshaft positioning sensors Your fuel injection computer (DME) may output a code that indicates a faulty camshaft position sensor (CPS). This important sensor tells the car's computer where the flywheel is located in relation to the combustion cycle. The DME takes the signals from both the cam position sensor and crankshaft position sensor, and calculates when to fire the fuel injectors and spark plugs. If the crankshaft position sensor is not operating properly, your car will run very erratically or perhaps not at all. Replacement of the sensor is not as easy as the camshaf...
Read more

Yaw Rate Sensor Replacement - C Class - W204 - Mercedes-Benz

Image
Yaw Rate Sensor Replacement - C Class - W204 - Mercedes-Benz Yaw Rate Sensor Replacement Time: 2 hours Tab: $320 Talent: 2 Tools: Trim removal tool, E12 socket, T45 Torx driver, 10mm socket or wrench Applicable Models: Mercedes-Benz C250 (2012-14) Mercedes-Benz C300 (2008-14) Mercedes-Benz C350 (2008-14) Parts Required: Yaw rate sensor Hot Tip: The sensors are sensitive to shock; use care when working with them Performance Gain: Working ESP Complementary Modification: Clean carpet and interior beneath seats The yaw rate sensor is located below the driver side seat and is used to measure the yaw, lateral and longitudinal acceleration of the rotation around a vertical axis. This sensor is used to supply information to the Electronic Stability Program and has been known to fail in the past. If you are getting an error code for the yaw sensor and need to replace it this article will show you how. The sensors are sensitive to impact so use care when working with it and be ca...
Read more

Front Stabilizer Bar Replacement - C Class - W204 - Mercedes-Benz

Image
Front Stabilizer Bar Replacement - C Class - W204 - Mercedes-Benz Front Stabilizer Bar Replacement Time: 2 hours Tab: $170 Talent:2 Tools: E12 Torx, T40 Torx, 18mm, 13mm wrench Applicable Models: Mercedes-Benz C250 (2012-14) Mercedes-Benz C300 (2008-14) Mercedes-Benz C350 (2008-14) Parts Required: New stabilizer bar and hardware Hot Tip: Don't let the bar fall on you Performance Gain: Better handling If you are starting to hear a knock sound when you go around a corner there is a good chance your sway or stabilizer bar bushings are starting to go bad. Unfortunately, the rubber bushings on the stabilizer on the W204 are vulcanized to the bar and cannot be replaced separately. This means you will need to drop the bar and replace it with a new one. All of the mounting hardware is considered single use so make sure you order new hardware when ordering the bar. You will need to jack up the car and remove the front wheels along with the under body trays to perform...
Read more